Tossing black dress for some time, has been thinking about doing a tutorial, the province to find tutorials everywhere, but also for everyone to be a reference.
First, hardware articlesThe first is the installation of ideas, just beginning to think about the host with J3455, to count to go to the last G4600, power consumption is indeed high, but if the black skirt was blocked, and can be used for office.
Replaced by the previous monitoring of the hard drive, three 2t hard drives, two of which set up a raid1 to put photos and information, leaving a movie and television show and some unimportant files.
Last host diagram
More than one hard disk, the wiring is so troublesome, so it is.
In front of a fan, the hard disk temperature is still quite high.
With the power consumption diagram, the standby power consumption is about 47W, the full load power consumption is about 70W, where our electricity fee is 0.55 yuan, and the lowest power consumption is 47*24*365/1000*0.55=226.45 yuan, which is basically empty. The annual electricity bill should not exceed 300 yuan. Relatively digital disk is still more cost-effective.
Only black skirts, it is recommended to use J3455 or J4105 these low-power U, Taobao has a whole machine to sell, usually around 1200 yuan, their own words can be cheaper. There is no need to add SSDs.
First of all, you need to make a boot disk, ready a U disk, 1G on the line (it is difficult to find a smaller one now)
Attach tools collection: link Password: qj2r
1. Open the chip without worry, record the VID and PID of the U disk, as shown
2. Install OSFMount and run
Choose Mount New
Add 3615XS file, select Partition 0, click OK
After checking the option of Read-only drive below, click OK
Double-click the image in OSFMount to open the grub directory and edit the grub.cfg file
Set vid=0x058f changed to U disk VID
Set pid=0x6387 changed to U disk PIDset
Sn=A8ODN02468 serial number brush half white group needs to be changed
Set mac1=0011322CA603 mac address hard white dress need to be modified, usually negligible
After the modification is complete, click Dismount all & Exit and select Yes to save.
3. Burn U disk,
Install Win32 Disk Imager and run as shown below
The first step is to select the U disk; the second step is to select the boot file that has just been written; the third step is to click write and select Yes. Waiting for a moment will prompt a successful write.
4. Install the system
Insert the USB flash drive into the computer, set the U disk in the BIOS to boot, as shown in the following figure (the following is borrowed, invaded)
After seeing the above figure, enter the input in the browser to search for DSM. If it is not found, install Synology Assistant to find it. You can also calculate the IP address of the machine on the router and enter the IP address in the browser.
Select DSM_DS3615xs_15217.pat and click Install Now
After the installation is complete, the computer will restart, wait for a while, refresh, as shown below, the specific content according to personal preferences.
At this point, the black skirt is installed and can now be upgraded to 6.1.7 (the latest version)
5. About whitening
At present, only semi-white wash, the first kit center --- practical tools --- docker select the installation kit
Then, click Settings --- Network --- Web Interface --- Management --- open vswtich settings --- open tick before open vswitch
Open the installed docker in the menu, select ddsm, and click Add 
No brain click Next, and finally click Finish
Wait a moment, after the installation is complete, as shown in the figure, the right connection
Well, enter a new dsm interface, open the settings, record the serial number of the product inside, follow the above steps to re-create the boot U disk, then photos and videos can be decoded.
1. How to change the root password
In the settings, open SSH
Use xshell to connect to your nas, first enter sudo -i to get root privileges, and then enter synouser --setpw root xxx (xxx is the password you want to change)
2. Install Transmission
In the Suite Center, select Settings.
Select the source of the suite, click Add, name enter tr (for casual input, this is a software library), location input
In the community will be able to find tr, click on the installation, after installation is complete, in the browser, enter your dsm ip address followed by: 9091 you can log in.
How to change the interface
3. How to install emby
Like the above settings, it is not on the map, address
Very good use of the playback server, so that when the film is transcoded, my g4600's core should be able to use
IV. ConclusionIn general, I feel that I wrote carefully enough. If you still can't read it, don't toss it. If you have money, buy a white dress. After all, people have to eat.
Fast thyristors (Inverter Thyristor)are used for higher frequency rectification. Inverter and inverter circuit appliances.
Rectifiers have many uses, but are often found serving as components of DC power supplies and high-voltage direct current power transmission systems. Rectification may serve in roles other than to generate direct current for use as a source of power. As noted, detectors of radio signals serve as rectifiers. In gas heating systems flame rectification is used to detect presence of a flame.
Inverter Thyristor,Power Inverter Thyristor,Frequency Inverter Thyristor,Electronic Component Inverter Thyristor,Bi-directional Controlled Thyristors (BCT)
YANGZHOU POSITIONING TECH CO., LTD. , https://www.cndingweitech.com